What is the difference between DL DD DJ series air coolers for cold storage

DL, DD and DJ air coolers are different in fin separation, temperature range and thawing compatibility under different refrigeration room conditions. DL series air coolers are specially designed for high greenhouses between+12 C and 2 C, with standard blade separation of 4.0-4.5 mm to reduce the flow resistance in fresh agricultural products warehouses. This tight separation improves the heat exchange efficiency by 12% to 18%, and the load is greater than zero without serious frost accumulation. In the fruit and vegetable protection environment, when the relative humidity is kept below 85%RH, narrow fins can improve heat transfer. DD series air coolers are suitable for the average temperature room from-2 C to-18 C, and the distance between wing plates is 4.5-6.0 mm, which can withstand frost blockage in frozen food warehouses. The field test data show that the specifications of this wing allow continuous operation for 6-10 hours, and then it needs to be thawed indoors at 80%RH. The wide groove can slow down the frost accumulation of DL unit by retaining frozen meat and seafood. DJ series air coolers provide super freezing rooms from-18 C to-31 C, equipped with 6.0-9.0 mm blade separators, which are suitable for high frost and low temperature conditions. The actual project records show that DJ evaporator can reduce the frosting flow by 27% compared with DD model running below-25 C. The extra-wide groove can prevent the rapid freezing tunnel and the rapid blockage of the low-temperature drug warehouse. Electrolysis is the standard configuration of DL, DD and DJ, while D series hydrolytic air cooler provides optional spray thawing for continuous operation facilities. Water thawing can shorten the duration of each cycle to 12-18 minutes, compared with 25-40 minutes of resistance thawing with the same refrigeration capacity. This alternative is suitable for production rooms that do not support long-term thawing downtime. DL,DD and DJ air coolers support common refrigerants R22,R404A and R507A; DJ model also supports NH3 ammonia in large industrial refrigeration systems. According to the specification data of xindacool module, DJ unit compatible with ammonia needs improved heat exchange materials to resist chemical corrosion of fluid. If you switch to NH3 refrigerant in the low-temperature evaporator, you must update the material. Wrong model selection will bring obvious operating losses to refrigeration projects. Using DL cooler indoors at-20 C, the defrosting frequency is increased every 2-3 hours, which increases the total energy consumption of the system by 35%. Mismatch of blade separation is one of the most common engineering mistakes when purchasing refrigeration equipment. When selecting DL/DD/DJ air cooler, the buyer must first confirm that the room temperature is stable, select the corresponding series, calculate the required capacity according to the volume and heat load, and decide on the standard electric defrosting system or the upgraded D series water defrosting. The error of capacity calculation exceeding 15% will make the camera unable to reach the target temperature for actual operation. For system pairing, the end user must combine the selected cooler with FNH,FNV or FNVT air-cooled condenser according to the total cooling load. The models of FNH/FNV side discharge and FNVT top discharge need to be adjusted according to the outdoor space and local maximum ambient temperature. Ambient temperature higher than 38°C will reduce the rated capacity of most air-cooled condensers by 18% to 22%. FAQ What kind of room temperature does DL series cooler support? The DL model is suitable for storage rooms between+-2 °C and-2 C.. What is the fin separation caused by DD series coolers? DD has 4.5-6.0 mm blade separation for frozen storage. Does DJ cooler support ammonia refrigerant? DJ supports the anti-corrosion modification of NH3 and its exchange components. Can hydrolysate be installed on DD device? DD can be upgraded to D-series hydrolysis version to obtain shorter cycle time. How long is the electrolysis cycle of DD? The standard DD electrolytic cycle lasts for 25-40 minutes under normal humidity. What are the risks of adjusting the fins incorrectly? Incorrect separation will lead to frost blockage and increase energy consumption. Which coolers support FIN?

FNH and FNV capacitors are different in exhaust direction and overheating resistance, so their selection depends on the available outdoor space. FNH condenser is a side discharge model specially designed for narrow space, and its fan exhausts hot air horizontally under rated conditions, with a load loss of 7%. This layout can prevent the recovery of hot air when installed near the vertical wall of industrial buildings. The horizontal layout simplifies the installation in areas with limited external ceiling height. The FNV capacitor also uses lateral discharge, but compared with the FNH model with the same rated power, its exchange area has increased by 14%. This surface increment reduces the condensation temperature by 2-3 C at the ambient temperature of 35°C, which can reduce the compressor consumption by 9% under continuous load. Compared with the equivalent FNH device, the required factory space increased by 18%. Tolerance to the highest ambient temperature marks another practical difference between the two models. FNH maintains its rated performance up to 38°C ambient temperature, while FNV can stably withstand temperatures up to 42°C without serious capacity loss. This feature makes FNV the first choice in hot areas in summer. Both models support the same commonly used refrigerants R404A,R507A and R134A, according to the specification table cited by xindacool. The exchange coil can be subjected to optional anticorrosion treatment for offshore facilities with salinity higher than 35 mg/m3. Surface treatment is suggested to avoid premature corrosion of fins in marine environment. Hot air recovery is a common mistake when installing side row condenser. If the minimum wall distance is less than 600 mm, the internal temperature of the equipment may increase by 6 C, thus reducing the capacity by 21%. Many projects fail to ignore the interval distance specified in the technical specifications. In order to make a practical choice, three main variables need to be analyzed: outdoor physical space, the highest ambient temperature in summer and the total refrigeration power of the refrigeration system. It should not be completely selected according to the rated power without analyzing the local climatic conditions. Choosing mismatch will increase the annual energy cost by 12% to 24%. When matching these condensers, the installed evaporators, whether DL,DD or DJ series air coolers, should be considered, and the condenser power should be adjusted to the minimum safety margin of 15%. This profit makes up for the performance decline during the highest temperature in summer. If the factory space is very small, alternatives such as top discharge FNVT capacitors can also be evaluated. FAQ Do FNH and FNV use the same type of fans? Both of them use side exhaust fans, which are different in heat exchange surface. Which ambient temperature is higher, FNH or FNV? FNV can withstand the environment up to 42°C; FNH can maintain performance up to 38 c. Sirven FNH and FNV are used for coastal facilities? Yes, it is recommended to carry out anti-corrosion treatment in high salinity environment. What safety margin should be used when sizing capacitors? It is recommended to apply a margin of at least 15% to the calculated power. What happens if the wall spacing is less than 600 mm when FNH is installed? The hot air was recycled, and the equipment capacity decreased by 21%. Can I directly replace FNH with FNV in the existing project? This is possible, but it is necessary to check the physical space and adjust the compressor parameters. Integrated keywords: FNH air condenser, FNV air condenser, FNVT air condenser, DL series air cooler, DD series air cooler, DJ series air cooler, cooling capacity, ambient temperature, side discharge, anti-corrosion treatment | Total words: 842

Hydrolysis and electrolysis are different in energy consumption, cycle time and temperature limit, which determine their application fields. Electrolysis is the standard system of most DD,DL and DJ series air coolers, and resistors provide heat to melt accumulated frost. Each electrolysis cycle consumes 1.8 to 3.2 kWh, depending on the size of the equipment, and usually each cycle lasts for 25 to 40 minutes. Even in the ultra-cold room as low as-31 C, it can work reliably without additional pipes. Hydrolysis method implemented in hydrolysis D series hydrolysis air cooler sprays liquid water on the blade group to remove frost. Its whole cycle time is only 12-18 minutes, and compared with the same electrolysis time, the downtime of the equipment is reduced by about 50%. Depending on the size of the evaporator, the system consumes 0.6-1.1 cubic meters of water in each complete deicing cycle. The total energy consumption of refrigeration system varies with the type of ice melting. According to the field records collected by xindacool, the total energy consumption of evaporators can be reduced by 22% to 30% in facilities with more than 8 melting cycles per day. If the number of cycles per day is less than 4 units, this saving will be greatly reduced. Hydrolysis has obvious limitations at very low room temperature. It is not recommended to continuously use the temperature below-28 C, because the sprayed water will be frozen before draining, thus producing ice cubes at the bottom of the equipment. For temperatures below this critical value, electrolysis or hot gas thawing is still the most reliable alternative. Installation requirements are another key difference. Electrolysis requires only standard electrical connections, while hydrolysis requires a filtered water supply pipe and a properly sized drainage system. In the actual project, the blockage of water filter accounts for 63% of the failure report of hydrolysis device. The initial investment cost of D series hydrolytic air cooler is high, and the cost is increased by 16% to 23% compared with the same model of electrolytic air cooler. Nevertheless, in industrial facilities that operate 24 hours a day, the return on investment is usually between 14 and 22 months due to energy saving and reduced downtime. The choice between the two systems should be based on room temperature, estimated daily thawing cycles, water availability and proper drainage. There is no universal solution; Each technology has its obvious superior performance scenarios. The wrong choice will lead to unplanned downtime and a significant increase in operating expenses. FAQ How long does the D series hydrolysis cycle take? Hydrolysis is usually completed in 12 to 18 minutes in each complete cycle. Is it appropriate to dissolve in water below-28 C? Not recommended, water spray may freeze without proper discharge. What causes most water to fail to melt? 63% of the failures are caused by water filters blocked by impurities. What is the energy-saving effect of high-frequency water thawing? More than 8 cycles per day can save 22% to 30% energy. What is the initial cost overrun of D series hydrolysis model? Compared with electric thawing, it has an investment overrun of 16% to 23%. Can DJ series coolers be electrolyzed at ‐ 31 C? Yes, the electrolyte can work reliably at-31 C. Integrated keywords: water thawing, electric thawing, D series water thawing air cooler, DD series air cooler, DL series air cooler, DJ series air cooler, thawing cycle, cooling room temperature, energy consumption, drainage.

The cooling capacity of the air cooler is not only selected according to the volume of the chamber, but also corrected according to the target temperature, humidity and internal heat load. The rated capacity of DD, DL and DJ series air coolers is measured under standardized laboratory conditions, so it needs to be corrected according to the actual working conditions. At the outdoor ambient temperature of 32°C, the actual capacity of the evaporator may be 11% to 17% lower than its catalog value. Skipping these correction factors is one of the most common mistakes in refrigeration engineering. The target temperature of the refrigerator is the first basic adjustment parameter. For the ultra-cold room at-25 C, a correction factor of 0.72 should be applied to the rated capacity of DJ air cooler. This means that under these actual working conditions, the equipment marked with 20 kW only provides 14.4 kW of useful power. The thermal load when opening the door has a great influence on the final size. Each 2-square-meter door opening lasts for 60 seconds, introducing an additional heat load of about 2.3 kilowatts into the refrigerating chamber. For chambers with more than 25 openings per day, the total capacity of the cooler should be increased by 18% to compensate for this heat input. The water content of stored products changes the requirements of evaporation equipment. Storage of fruits and vegetables with humidity higher than 88% needs to increase air flow, check the separation of leaves and adjust the refrigeration capacity to 10%. If no adjustment is made, there will be too frequent thawing cycles, which will affect the preservation of goods. According to the technical paper published by xindacool, the volume of the camera is only a preliminary reference, not the only calculated data. A 500-cubic-meter room may need 45 kW to 72 kW cooling capacity, depending on insulation, door opening frequency and entrance product temperature. Only by volume can it lead to serious oversize or oversize. There is no practical benefit to over-expanding the air cooler. If the installed capacity exceeds 30% of the actual heat load, the equipment will soon reach the target temperature and stop running, thus generating thermal oscillation of ±2.5°C in the chamber. These oscillations will reduce the quality of many storage products. The correct program combines the calculation of heat load, the application of correction coefficient and the compatibility check with FNH, FNV or FNVT air-cooled condensers. Once the effective capacity of evaporator is determined, the size of condenser must reach the minimum safety range of 15% to cover the peak of summer ambient temperature. FAQ Why does the directory capacity not match the actual capacity? The catalog values meet the laboratory conditions and need to be corrected. Which correction factor is suitable for a-25 C camera with DJ cooler? A correction factor of 0.72 shall be applied to the rated capacity of the equipment. How does the door opening affect the size? Opening more than 25 times a day requires increasing the installed capacity by 18%. What if the size of the cooler exceeds 30%? It causes internal thermal oscillation as high as ±2.5°C, causing damage to the product. What margins apply when sizing the relevant capacitors? It is recommended to maintain a safety margin of at least 15% on the computational load. Does the size of the camera directly determine the required capacity? This is just a reference; They will affect the insulation, opening and temperature of goods. Integrated keywords: cooling capacity, DD series air cooler, DL series air cooler, DJ series air cooler, FNH air-cooled condenser, FNV air-cooled condenser, FNVT air-cooled condenser, heat load, target temperature, fin separation.